The following information covers factory service procedures for servicing the throttle body on MerCruiser inboard engines. Procedures applicable to the 5.0L/5.7L/6.2L MPI gasoline engines for 2001 2002 2003 2004 2005 and 2006 models.
STERNDRIVE MCM
- 5.0L V8 MPI Alpha and Bravo
- 350 MAG MPI Alpha and Bravo
- MX 6.2L MPI Horizon
- 350 Mag MPI Alpha and Bravo Horizon
- MX 6.2L MPI
INBOARD AND TOW SPORTS (MIE)
- 350 MAG MPI Inboard
- MX 6.2 MPI Horizon Inboard
- 350 MAG MPI Horizon Inboard
- MX 6.2 MPI Inboard
- 350 MAG MPI Tow Sports
Testing and diagnosis helps determine problems and possible causes. Its important to perform extensive testing and troubleshooting prior to any major tear down or repair work. This ensures that the full extent of the problem is understood beforehand and may prevent any unnecessary repair work. Its recommended you use a factory repair manual when performing repairs on any vehicle, additional safety precautions, or technical data maybe included.
THROTTLE BODY REMOVAL
1. Take off the engine cover and the flame arrestor.
2. Detach the throttle linkage from the throttle body.
3. Detach the harness connector from the throttle position sensor.
4. Take off the IAC hose from the throttle body.
5. Take off the throttle body attaching studs.
6. Remove the throttle body.
7. Take off the throttle body sealing ring and discard it.
IMPORTANT: Place a clean towel over the opening of the intake manifold to prevent items or debris from entering the hole of the engine.
CLEANING AND INSPECTION
IMPORTANT: Never use any cleaners that contain methyl ethyl ketone.
IMPORTANT: Avoid getting any cleaners or solvents on the TPS (throttle position sensor).
IMPORTANT: Avoid damaging the throttle body or adapter when removing any gasket material from the throttle body and adapter.
1. Carefully remove any gasket material from throttle body and adapter, be sure not to damage the sealing surface.
2. Take off the IAC muffler.
3. Clean all of the throttle body parts thoroughly. Make sure that all of the passages are free of burrs, dirt and debris.
4. Carefully check the sealing surfaces for damage that may effect the gasket from sealing.
5. Inspect the throttle body casting for damage or cracks.
6. Check the linkage, throttle plates and other components for wear, damage and foreign material.
INSTALLATION
1. Reinstall a new throttle body sealing ring into the grove in the throttle body.
2. Reinstall the throttle body onto the upper intake manifold and align the dowels.
3. If your going to be reusing the fasteners, first apply adhesive (Loctite 242, part number 92-809821) to the threads of the throttle body attaching studs.
4. Reinstall the throttle body attaching studs and torque the studs to 9 Nm 80 lb-in.
5. Reinstall the IAC muffler.
6. Reinstall the throttle cable bracket.
NOTE: Make sure that the stud and nut are threading properly. Torque the throttle cable bracket nut to 19 Nm 168 lb-in.
7. Reinstall the IAC plug to the IAC hose.
8. Reinstall the flame arrestor and torque the flame arrestor retainer bracket nut to 12 Nm 108 lb-in.
9. Reinstall the engine cover.
MerCruiser Throttle Information
- 2001 mercusier 6.2 mpi trottle body gasket
- mercruiser 5.0 trottle body diagram
- 1988 mercruiser 4.3l throttle lever
- 1988 mercruiser quicksilver throttle control for alpha 1
- 1992 mercruiser 5.0 overheats when full throttle
- 1992 mercruiser throttle control replacement
- 4.3 mercruiser runs hot at full throttle
- how do i adjust the throttle on a 1998 sea ray 4.3l mercruiser alpha 1
- how does the linkage for a mercruiser throttle body go together
- how to adjust throttle on 1965 merc 650
- mercruiser 3.0 overheating when opening up throttle
- mercruiser 350 mag throttle body cleaning
- mercruiser 5.0 efi throttle body fuel pressure sensor
- mercruiser 5.0 over heating at full throttle
- mercruiser 6.2 mpi throttle position
- mercruiser 6.2 problems when throttle
- mercruiser controller 1995 4x3l throttle control how to remove?
- mercruiser horizon 8.1 throttle position sensor
- mercruiser iac throttle body connector
- mercruiser inboard throttle
- mercruiser overheating at full throttle
- mercruiser throttle control alpha one gen 2
- mercruiser throttle service
- mercruiser5.7 surge in throttle
0 comments:
Post a Comment